PRODUCT NAME SLB04 Wharf special steel pile paint

BRIEF  A One Pack Acrylic resin Topcoat

FEATURES
-Excellent ageing resistance
-Excellent salt spray resistance
-Excellent resistance to chalking and cracking  -widely used topcoat
-Excellent compatibility with kinds of coating

RESISTANCE GUIDE
HEAT RESISTANCE         Should not be used in high temperature environment 
WEATHERABILITY           Good gloss and colour retention when exposed 
SOLVENTS                       Should not be direct contact with various organic solvents  CHEMICAL RESISTANCE         well
SALTS                      Excellent resistance to neutral and alkali salts
WATER                    Excellent resistance to fresh and salt water, but immersion
ABRASION              Good when fully cured.
USES:Used inside and outside of steel and concrete, in all kinds of weather conditions. Dry quickly, Can be used under low temperature conditions.

TYPICAL PROPERTIES AND APPLICATION DATA
COLOR                         Colors
DENSITY                       1.25g/cm3
SOLIDS BY VOLUME              46%
SOLIDS BY WEIGHT               68%
SPREADING RATE                7.36 m2/kg   (50um DFT)
DRYING TIME(23℃)              Touch  1 Hr    Handle  24 Hr
OVERCOAT INTERVAL(23℃)        Min 4 Hr   Max none 
STORAGE                         at least 12 months (dry, cool and under cover )
PACKAGING                     20kg/ bucket

DIRECTIONS Before using stir or using dynamic mixer mixing two components completely,Just mix a good raw material and mixing of raw materials before can not be together. Rate of cure will vary depending on temperature and other factors such as ventilation, film thickness, humidity, thinner. The temperature of stir will >15℃, otherwise thinner should be added for needed viscosity after stir.
Overmuch thinner will lead sag and slow cure rate, thin film, thinner should be added after mixed. Practical spreading rates may be reduced 5%—25% for wastage of different application conditions.

APPLICATION STEEL:The surface coated by primer or intermediate paint should be dry and clean, no oil and other pollutants. When overcoat on a two-component film such as epoxy paint,wharf's pavement quality for old film should be taken if more than the longest accordance with time.Don’t apply at temperatures below 5℃ or above 40℃. Don’t apply at relative humidity above 85% or when the surface is less than 3℃ above the dewpoint. Don’t apply if there is fog, rain, snow or strong wind.

BRUSH/ROLLER: Suitable for small areas only. Apply even coats of the mixed material to the prepared surface. Thin if necessary with up to 0-5% with Special Thinner. Additional coats may be required to attain specified thickness.
CONVENTIONAL SPRAY: Thinning is not normally required, however 0-5% of Special Thinner can be added.
AIRLESS SPRAY: Thinning is not normally required, however 0-5% of Special Thinner can be added. Pump ratio is 32:1 or 45:1 and fluid tip is 0.43-0.48 mm.
Overcoating: Aged coating should be tested for lifting by a method such as ‘X’cut or crosshatch methods. If it lifts, remove it. The surface must be free of oil, grease and other contaminants.
Previous coat: Epoxy resin coating, Chlorinated rubber paint
CLEAN UP: with Epoxy Thinner X-3

SAFETY:Pay attention to the safety precautions before and after using this product. Users should comply with the provision of the respective country or local government. It’s dangerous or deadly to eating it. To avoid inhalation of thinner steams and spray mists.
Use protective wears correctly; the skin and eyes should avoid contacting it. Use with good ventilation. This product is flammable. All sources of ignition must be eliminated in, or near the working area. DO NOT SMOKE. Fight fire with foam, CO2 or dry chemical powder. On burning will emit toxic fumes.

Notes: The data in the manual is get from standard experiments and may be vary from different conditions in use. Please refer to the latest manual if the data is altered and we would not inform specially.